MODEL 310

STRUCK LEVEL 185 CU. FT., 310 BU. SHOWN WITH OPTIONAL TOP BEATER. UNLOADING SPEED FOR THE 310 SPREADER - (2 SPEED CHAIN DRIVE) HIGH SPEED: PTO SPEED 540 RPM. 8 FT 8 1/2 IN PER MIN. - LOW SPEED: PTO SPEED 540 RPM. 4FT 8 1/2 IN PER MIN. FRONT SPLASH GUARD IS STANDARD EQUIPMENT. 

OPTIONAL REAR PAN

THE REAR PAN IS OPTIONAL ON THE MODEL 310.    

MASSIVE UNITIZED WELDED FRAME

H&S SPREADERS HAVE A MASSIVE UNITIZED WELDED FRAME WITH HEAVY FLOOR SUPPORTS AND SIDE STAKES, WRAP AROUND STEEL FRONT CORNERS. STRONG REAR MAIN BEATER SIDE PANELS ARE SLANTED FOR CLEARANCE AND WIDER SPREAD, AND THEN WELDED TO THE STRONG 5'' U CHANNEL SIDE MEMBERS. COMPARE WITH ANY ON THE MARKET.

REINFORCED PLYWOOD

SIDES, FRONTPANEL AND BOTH SIDES OF THE REAR HYDRAULIC END GATE USE FIBERGLASS REINFORCED PLYWOOD TO PROVIDE FOR EASY CLEANING AND MINIMAL FREEZE UP. THE 310 HAS A SOLID VIRGIN GRADE POLY FLOOR. CONSIDERABLY LESS TORQUE IS NEEDED TO MOVE A HEAVY LOAD.

OPTIONAL TOP BEATER

MODEL 310 CAN BE EQUIPPED WITH THE OPTIONAL TOP BEATER TO PROVIDE LOAD LEVELING AND SPREADING OF HIGH HEAPED LOADS. NOTICE HOW BOTH BEATERS HAVE NO OBSTRUCTIONS TOWARDS THE SIDES AND REAR TO PROVIDE FOR BETTER SPREADING.

 2-SPEED APRON DRIVE

THE 2-SPEED APRON DRIVE IS STANDRAD EQUIPMENT. AN OPTIONAL VARIABLE SPEED HYDRAULIC DRIVE IS ALSO AVAILABLE.

OPTIONAL SECOND HYDRAULIC ENDGATE CYLINDER

AN OPTIONAL SECOND HYD. ENDGATE CYL. IS AVAILABLE FOR THE MODEL 310. THE HYDRAULIC LINES ARE RUN THROUGH A 3 X 3 TUBE UNDER THE FLOOR. THE UPRIGHT POSITION OF THE HYDRAULIC CYLINDER STROKE ALLOWS THE GATE TO LIFT WITH THE LEAST STRAIN AT PIVOT POINTS. A SEMI-LIQUID HYDRAULIC END GATE IS STANDARD EQUIPMENT.

29'' DIAMETER BEATER

THE MODEL 310 SPREADER HAS A 29'' DIAMETER BEATER WITH 14 REPLACABLE PADDLES. THE BEATER HAS TWO TYPES OF PADDLES, BLUNT FOR WIDESPREAD AND SHARP RIPPER TYPE FOR CUTTING AND SHREDDING. THE BEATER SIDE WIPER BLADES ARE STANDARD.

OIL BATH BEVEL GEAR BOX

THE STRONG OIL BATH BEVEL GEAR BOX THAT POWERS THE BEATER IS TAPERED TIMKEN ROLLER BEARING EQUIPPED. ALSO SHOWN IS THE REPLACEABLE SPLINED HUB THAT WELDS INTO THE MAIN BEATER TUBE. THE GEAR BOX UTILIZES A 4-JAW BEATER SHUTOFF CLUTCH AND TRACTOR SIZED SPLINE SHAFT.

TIMKEN TAPERED ROLLER BEARING EQUIPPED

GEAR BOX MECHANISMS AND DRIVE FOR THE BEATER AND APRON ARE TIMKEN TAPERED ROLLER BEARING EQUIPPED. THE BEATER DRIVE GEAR BOX IS 1-1 1/2 BEVEL GEAR OIL BATH EQUIPPED WITH A 4-JAW OVER RUNNING CLUTCH FOR BEATER SHUTOFF. THE APRON DRIVE IS A 50:1 BRONZE WORM GEAR WITH SHEAR BOLT PROTECTION. 

EASY MAIN APRON ADJUSTMENT

ADJUSTMENT FOR THE MAIN APRON IS EASY, BY SIMPLY LOOSENING THE TWO SIDE BOLTS AND DRAWING UP THE LONG BOLT.

STEEL ALLOY APRON IDLER

H&S USES CAST SPECIAL STEEL ALLOY APRON IDLER SLIDES INSTEAD OF IDLER SPROCKETS MAKING FOR YEARS OF DEPENDABLE SERVICE.

VARIABLE HYDRAULIC DRIVE

AN OPTIONAL VARIABLE SPEED HYDRAULIC DRIVE IS ALSO AVAILABLE.